Author |
Topic |
|
Sunbeam-mike
United Kingdom
165 Posts |
Posted - 02 Jan 2017 : 09:10:55
|
Happy New Year everyone
Arrocuda - Thanks. Any help gratefully received. Let me know how much.
JPS - I'll send him a message.
Mike Hooper |
|
|
JPSH120
United Kingdom
1180 Posts |
Posted - 31 Dec 2016 : 16:20:30
|
Hi Tim,
I was thinking of floor pans, especially front.
Mike - have a word with Paul Marshall on here, he might be able to help with the sill trim caps.
___________________________________________________________________________
|
|
|
arrocuda
United Kingdom
501 Posts |
Posted - 30 Dec 2016 : 15:47:00
|
Can't help with the door and the sill trims. The guy I bought the project car off had put them all aside for 'safe' keeping, then lost them. Think I've got the plastic cover for the steering column and got some spare bumpers that would probably yield a decent overrider rubber between them.
Tim
Building the 'Mark II' fastback Rapier ('Arrocuda'). |
|
|
Sunbeam-mike
United Kingdom
165 Posts |
Posted - 30 Dec 2016 : 10:33:04
|
Hi Dev, Arrocuda
A bit of a long shot after all this time I know but I'm interested in the 'floor door trim'. Are these the strips across the bottom of the door aperture?
Also, if you have them, the trim pieces that hide the front edges of the stainless sill covers, a battery clamp, an H120 wheelnut, the door switches that are like crosshead screws, an overrider rubber, and most annoyingly the top half of a steering column cowl that fits around an adjustable steering wheel.
All lost, broken or misplaced during a 10 year rebuild I'm afraid.
Thanks,
Mike
Mike Hooper |
|
|
arrocuda
United Kingdom
501 Posts |
Posted - 25 Dec 2016 : 11:48:44
|
Hi Jason.... Is probably easier for you to tell me what you need and I'll check it out during the week cos I'm working on the engine right now. So far I've taken off the inner front wings with the strut tops and they are in excellent nick. The rear inner and outer arches are also very clean and solid. The boot floor is also ok although it looks like it has had a couple of holes drilled through it at some time in its past, but would probably need a strip welding on to the trailing edge as the rear valence panel is virtually non existent. Hard to tell for sure whilst it's still in situ.
Of the bits in between, the sills are rough and the floor is good in the rear, but thin in the frontal areas with holes in the footwells. Rear quarter panels and inner wings are also good.
Tim
Building the 'Mark II' fastback Rapier ('Arrocuda'). |
|
|
JPSH120
United Kingdom
1180 Posts |
Posted - 23 Dec 2016 : 17:15:21
|
Tim, let me know what repair panels you've got.
Cheers.
___________________________________________________________________________
|
|
|
arrocuda
United Kingdom
501 Posts |
Posted - 22 Dec 2016 : 08:53:30
|
I'm sorting out a fair amount of duplicate stuff a lot of which I'm unlikely to need. Also got some repair panels if anyone's interested. What are you looking for?
Tim
Building the 'Mark II' fastback Rapier ('Arrocuda'). |
|
|
minicuda
USA
2 Posts |
Posted - 21 Dec 2016 : 23:25:28
|
Hi, I am curious to know if you still have these parts or other parts for the Fastback. i have a 1970 Alpine GT. Thanks |
|
|
kakarot
Croatia
1 Posts |
Posted - 13 Mar 2014 : 13:08:37
|
Hi, I am interested in rear screen seal, floor door trim and front screen chrome trim.
Josip Orešković |
|
|
chazr
United Kingdom
72 Posts |
Posted - 26 Nov 2011 : 14:03:55
|
Hi i am intrested in the headlight holding surronds, rear screen seal,wiper blades,and the bonnet pull cord and fuel cap. my email address is chubbycharl@hotmail.co.uk thanks chaz |
|
|
devnet H120
United Kingdom
81 Posts |
Posted - 26 Nov 2011 : 10:14:08
|
Hi Guys,
I have a range of fastback parts for sale in varied condition, I got them from a big job lot of parts so I am getting rid of what I do not need. They either came off a Rapier Fastback or an Alpine Fastack. See the list below if your interested reply with your email address I will send pictures and details. Open to sensible offers.
Cheers,
Dev
Stromberg Carb/Air Box/Inlet Manifold Break & Clutch Pedal Unit Fuel Cap Chrome Full Head Dash Shelf Rear Light Cluster Units Fullx2 Full Wooden Dash + Clocks etc. Glove Box Rear view mirror Bonnet Pull cord and handle Headlight Holding Surrounds 2x Glass Quarter Lights with hinges 2x Windows Full Heater Unit 4x Chrome Wheel Trims Handbrake Anti Role Bar (New) Sunvisors Headlight Surrounds x2 Windscreen Wipe Motor Mech Horn & Beam Indicator Stalk Heater Control Mech Wiper Blades Chrome Interior Centre Light Screen Heater Vent Pipes Floor Door Trim Various Seals Rear Screen Seal Front Screen Chrome Trim Radiator Fan
devnet H120 |
|
|
Topic |
|